Tubular Steel ProductsInterior FurnishingsTherapy and Rehabilitation BedsBock Manual – centroflexAssembly andOperating Instructions
18 19 If the maximum adjustment time of two minutes is exceeded, for instance through fiddling with the hand control, and if the motors overheat, the
20 21 Key for disabler Knob position 1 Hand control functions activeKnob position 2 and control functions deactivatedKnob positions 3 and 4 are set
22 23The principle of the housing for the OKIMAT dual drive unit and linear OKIDRIVE guarantee that all components will con-tinue to function for a lo
24 25 6. Accessories Hermann Bock GmbH offers practical accessories that pro-mote mobility to ensure that every care bed can be tailored to the speci
26 27 6.3 Assembling accessories The following standard accessories can be combined with every Bock bed model:Attachable siderails, 3.8 kg (Fig. 1)Pa
28 29 6.4 Mattresses Basically all foam and latex mattresses that have, at least, a volume weight of 35 kg per cubic meter and do not exceed a height
30 31 7. Setting up and operating – centroflex 7.1 Design and purpose The centroflex was especially conceived for the demands of daily long-term u
32 33 7.4 The centroflex ready for use Before you proceed with assembly, fully remove the remai-ning packaging.1. Remove both of the screws with whi
34 35 7.5 Control The hand control is used to control the settings. The fol-lowing functions can be controlled by pressing the appropri-ate button on
36 37– Before reinserting the mains plug, visually check the mains cable for mechanical damage (bends, pressure points, abrasions and exposed wires).
3Dear Customer,In deciding to buy a therapy and rehabilitation bed from Bock you have opted for a care product that has a long service life and delive
38 39 8. Safety guidelines General safety testThe safety standards of an electrically driven care bed are regulated by adhering to the Euro Standa
40 41 Important safety requirements from 1.1.2001> The complete drive system including hand cont-rol has to be protected from water splashing (in
42 43Bock top guarantee 4: Thermal releaseIn the event that the electrical resistance with a short-circuit is not small enough, the mains isolation wi
44 45 Bock top guarantee 10: Moisture protectionThe drive housing meets the IPX4 protection level with its tongue and groove construction and is prot
46 47STK - List according VDE 0751-1Test specimen: ☐ Bed ☐ Insert frame ☐ Controller/main driveModel name: Series /inventory number: Location: Person
48 49declaration of conformityManufacturer: Hermann Bock GmbH Nickelstraße 12 D-33415 VerlProduct: carebed centro.flexClassifictaion: Medicine produc
50 51
Hermann Bock GmbHNickelstr. 1233415 VerlGermanyPhone: +49 (0) 52 46 92 05 - 0Fax: +49 (0) 52 46 92 05 - 25Internet: www.bock.netE-Mail: info@bock.
45 1. General information The various bed systems that are made by Hermann Bock GmbH meet the special requirements for use in rehabilitati-on and the
67 2. Cleaning, care and disinfection The individual bed elements are made of first-class mate-rials, largely from steel, whose surface has been give
89 3. General description of function 3.1. Structure and function Lying surfaceAll Bock care beds can be equipped with two different lying surface
10 11 3.2 How to assemble fast and easily: 1. Place the carrier elements with the pre-assembled Spiroplex spring elements on the cross-rails of the ly
12 13The leg sectionThe leg section consists of a two-part foot unit. Each indi-vidual position can be continuously adjusted by pressing a button on t
14 15 If you want the siderails back in the upper position as a pro-tection from falling out of the bed, get the upper siderail in the center of the
16 17 3.3 Caution: Risk of injury Proper use of all movable parts is essential to guarantee the safety of occupants, carers and nursing staff. The co
Commentaires sur ces manuels